
Level 2 Electrician Narwee
Looking for a Level 2 electrician in Narwee, NSW? Metering, service lines, supply upgrades, defect notices and emergency call outs, all of it Level 2 accredited work.
- Level 2 connection work. Metering, service lines and mains.
- 15 years across Sydney. Level 2 work is the whole business.
- Lifetime Labour Warranty. On every job we complete.
Same Day
Call Out*24 Hour
ElectriciansAll Payments
AcceptedLicensed and
Fully Insured
*Same day call out and the $0 call out fee are subject to availability, location and job type. Conditions apply, ask us when you book.
Local Level 2 Electricians in Narwee, NSW
Level 2 electrical work in Narwee covers everything on the connection between the network and your switchboard: consumer mains upgrades, overhead service line repairs and point of attachment repairs. It is accredited ASP work, it is the only work we do, and we do it right across Narwee and the St George area.
Found a notice from your distributor taped to the meter box? That is connection-side work, and it is what we are set up for.
What we are usually looking at in Narwee is the post-war housing around the station. Supply to most of Narwee comes in overhead, off a network pole to a bracket on the building, so the span and the attachment are usually where a job starts. Individual properties vary, and we confirm the arrangement at your address. The housing is largely post-war brick and fibro, and where no supply-side work has been done since, the mains feeding it may still be the original ones.
The dividing line is the connection itself. General electrical work inside the property is a licensed electrician's job. Work on consumer mains, overhead services, the point of attachment, metering, or authorised disconnection and reconnection requires an accredited Level 2 ASP. We hold both, are authorised on the Ausgrid network covering Narwee, and work to AS/NZS 3000:2018. 15 years, licence #482784C.

How Narwee Property Conditions Can Affect Level 2 Work
- Original supply on older housing: Consumer mains, attachments and switchboards on properties of this age are frequently the ones installed at build. Age alone is not a defect, but it does change what is worth inspecting first.
- Renovated and extended homes: Added air conditioning, electric cooking, pool equipment, gates, pumps or EV charging can change maximum demand calculations. The consumer mains and supply capacity should be checked against the proposed load.
- Established landscaping and finished driveways: Underground work may require route planning, conduit, excavation and reinstatement. A site inspection helps identify a practical option before the scope is finalised.
Our approach: We do not assume every Narwee property needs a complete upgrade. We identify equipment that is defective, unsafe or unsuitable for the planned load and recommend only the work required.

Consumer Mains in Narwee, NSW
Post-war Narwee housing was connected for a different pattern of use. Some properties still have their original consumer mains, which may or may not suit what has been added since.
Consumer mains upgrades in Narwee are Level 2 work because the supply has to be disconnected and reconnected at the network side. We handle the disconnection, the cable, the reconnection and the paperwork.
Worth a call if you have noticed ceramic fuses and rewirable fuse wire, consumer mains that look undersized for the load, or no safety switches on the board. Narwee is generally within the Ausgrid distribution area, so that is usually who the application goes to. We confirm it against your address before anything is lodged, because boundaries can run through a single street.

Our Services
All your Level 2 electrical needs covered
Our team has the skills, expertise and accreditation to cover any Level 2 requirement they come across. Every service is backed by safety, quality and experience.
Power Connect and DisconnectConnect a new property to the grid, or disconnect safely for demolition and works.
MeteringMeter installs, relocations and changes, with the paperwork handled.
Overhead Service LinesRepair, replace and install overhead service lines and storm damaged connections.
Underground Service LinesUnderground mains installed, located and repaired, including overhead conversions.
Consumer MainsInspect, repair, upgrade or install the mains feeding your switchboard.
Switchboard UpgradesAgeing fuse boards replaced with a compliant board and safety switches.We handle 23 Level 2 services in total. See the full list.
What we cover
Level 2 Electrical Services We Cover in Narwee, NSW
Every job below sits on the supply side of your main switch, which is the part that requires an accredited Level 2 ASP. If you are not sure which one describes your problem, describe it on the phone and we will tell you.
Consumer mains
The cable from the point of supply to your main switchboard. Replaced or upsized where it is damaged, unsuitable for the installation method, or too small for the assessed maximum demand.
Overhead service lines
The span between the network pole and your building. Replacement, re-tensioning, height and clearance corrections, and storm repairs.
Point of attachment
The bracket or fixing where an overhead service lands on the building. Repaired, relocated or replaced, including after storm damage.
Supply and capacity upgrades
Where current or planned demand exceeds what the existing connection can safely carry. Assessed against maximum demand, not against the age of the equipment.
Switchboards and main switches
Replacement boards, RCD protection and main switch work. Many switchboard jobs are general electrical work; a Level 2 ASP is needed where the job also touches the supply, the metering or the mains.
Overhead to underground conversion
Taking the span and the attachment off the building entirely. Scope depends on the cable route, the length, what else is already in the ground and what the connection point allows.
Metering and meter enclosures
Not all metering work sits under the same authorisation. Your retailer arranges the meter through a metering provider; the enclosure, the service equipment and any authorised disconnection and reconnection are Level 2 work.
Switchboard and meter box relocation
Moving the board or the enclosure for a renovation, an extension, better access, or to get equipment above a height that has caused a problem before.
Three phase upgrades
For sustained or heavy loads such as ducted air conditioning, pool plant, workshop or commercial machinery. Plenty of properties are better served by upsizing single phase, and the assessment decides which.
EV charger supply
Most home chargers run on single phase. The real question is whether the existing supply can carry the charger alongside everything else, which is a maximum demand question rather than a phase question.
Defect notice rectification
Rectifying what the distributor has listed, with the certificate lodged on completion. A notice is not a fine, but supply can be disconnected if it is ignored past the date on it.
Supply fault finding
Partial power, flickering, intermittent dropouts or a neutral fault traced with proper test equipment, so nothing is dug up or replaced on a guess.
Supply separation
A second dwelling, granny flat or tenancy needs its own supply, its own metering and its own main switch rather than a share of the existing one.
New connections and subdivisions
New supply for a build, a subdivision or a knockdown rebuild, including the distributor application and its lead time.
Emergency and storm damage
Cables down, attachments pulled out of a wall, burnt-out service equipment and total supply loss, 24 hours a day.
What changes the price of Level 2 work in Narwee
Whether the supply is overhead or underground, the cable size and the length of the run, access to the route, any excavation, conduit or reinstatement, whether metering or switchboard work is involved, how much distributor coordination the job needs, and whether it is planned or urgent.
Established gardens, paving and finished driveways affect the cable route, the excavation and the reinstatement more than the cable itself does.
We quote once the scope is confirmed on site rather than guessing from a photograph, not from a number over the phone.
0485 824 714St George
Level 2 electricians near Narwee
We work across the St George area regularly, so a job in Narwee often sits on the same run as these.
- Allawah
- Arncliffe
- Banksia
- Bardwell Park
- Bardwell Valley
- Beverley Park
- Beverly Hills
- Bexley
- Bexley North
- Blakehurst
- Brighton-Le-Sands
- Carlton
- Carss Park
- Clemton Park
- Connells Point
- Hurstville
- Hurstville Grove
- Kingsgrove
- Kogarah
- Kogarah Bay
- Kyeemagh
- Kyle Bay
- Lugarno
- Monterey
- Mortdale
- Oatley
- Peakhurst
- Peakhurst Heights
- Penshurst
- Ramsgate
- Ramsgate Beach
- Riverwood
- Rockdale
- Sandringham
- Sans Souci
- Turrella
- Wolli Creek
See everywhere we work in St George or browse every region we cover.
Service area
Level 2 Electrician Service Area Around Narwee, NSW
Narwee is part of our regular St George run rather than somewhere we travel to specially, which is what makes same day attendance realistic here rather than a promise we have to qualify.
- Covered from: our St George run, alongside the surrounding suburbs. See the whole St George area.
- Distribution network: Narwee is generally within the Ausgridarea. Boundaries can run through a single street, so we confirm it against your address before anything is lodged.
- Hours: Open 24 hours, 7 days. Emergency and after-hours attendance is quoted at its rate on the phone, before anyone is dispatched.
Also nearby: Allawah, Arncliffe, Banksia, Bardwell Park, Bardwell Valley, Beverley Park
Overhead Service Line Repairs in Narwee, NSW
The overhead service line is the cable running from the network’s pole to your building. Everything from the pole to the attachment is Level 2 work, which means it is not something a general electrician can legally touch.
We repair, re-tension and replace overhead service lines across Narwee, including after storms. If a line is down or hanging low, stay well clear, keep people and animals away, and treat it as energised even if the property has lost power. Contact your distributor, and call 000 if anyone is in immediate danger.

Where the Service Line Meets Your Narwee Home
The point of attachment is the bracket where the network’s service line lands on your building. It is the dividing line between their equipment and yours, and in Narwee it is where a fair share of supply problems begin.
We repair, replace and relocate points of attachment across Narwee. Point of attachment work requires an authorised Level 2 ASP. What isolation, disconnection and network coordination it needs depends on the existing service arrangement and the scope.

Power Supply Upgrades in Narwee, NSW
A supply upgrade is what you need when the property is asking for more than its connection was built to deliver. It is not the same as a switchboard upgrade, though the two usually happen together.
Power supply upgrades in Narwee can involve the service line, the consumer mains, the metering or the board. These are separate components, and an assessment determines which of them the work actually requires.

Is Your Narwee Switchboard Due for Replacement?
Post-war boards around Narwee are often full. Every way is used, nothing else can be added, and there may be no RCD protection on the circuits that matter.
We replace switchboards across Narwee. Whether the consumer mains need replacing at the same time depends on the assessment, not on the board alone. Boards from before the 1990s can have asbestos-containing backing panels, which we identify and plan around before starting.

Emergency Level 2 Electrician in Narwee, NSW
Supply problems do not keep business hours, and only a Level 2 electrician can legally work on the connection side when they happen.
Emergency Level 2 call outs across Narwee, day and night. Tell us what has happened and we will tell you honestly when we can be there rather than guessing at it.
Call 0485 824 714. Quotes are free.

Worth knowing first
Level 2 Electrical Work in Narwee, NSW: What People Assume
Most of the confusion we hear on the phone comes down to the same handful of things. Some of these mean you do not need us, which is worth knowing before you pay anyone.
A switchboard upgrade always means new consumer mains.
In practice: They are separate parts of the installation. A switchboard can often be replaced on its own. New consumer mains are required where the existing cable is damaged, unsuitable for the installation method, or too small for the assessed maximum demand. The assessment decides that, not the age of the board.
Every switchboard job needs a Level 2 electrician.
In practice: It does not. Many switchboard replacements are general electrical work and a licensed electrician can complete them. A Level 2 ASP is required where the work also affects the network connection, the consumer mains, the metering, or needs an authorised disconnection and reconnection. Worth establishing before the day rather than on it.
An old installation is automatically defective or undersized.
In practice: Age on its own is not a defect. Plenty of older supply equipment is in serviceable condition and compliant with what applied when it was installed. What matters is its actual condition and whether it suits the load the property now runs. That is an inspection, not an assumption.
Visible staining or rust means the equipment is unsafe.
In practice: Surface marking is a reason to look, not a diagnosis. Exposure may contribute to deterioration, but it does not establish that a given fitting has failed. Condition is assessed on the hardware itself, its mechanical load and what is behind the enclosure door.
One electrician handles everything to do with the meter.
In practice: Metering responsibilities and authorisations differ. Your retailer arranges the meter itself through a metering provider. The enclosure, the service equipment and any authorised disconnection and reconnection sit with a Level 2 ASP. We identify which parts apply to your installation and complete or coordinate them accordingly.
Properties in the same street have the same supply arrangement.
In practice: They often do not. One property may be fed by an overhead service to a point of attachment while the next has underground consumer mains from a pillar, and metering arrangements can differ again. We confirm what your address actually has before quoting or lodging anything.
Before we arrive
Staying safe until we get to you in Narwee
- If the power is out. Check whether the neighbours have power too. If the whole street is out it is a network fault and the distributor is already on it. If it is only your property, the problem is on your side of the connection, and that is the part we handle.
- Keep clear of damaged equipment. Never attempt to move, support or reconnect an overhead service cable, and do not touch the meter box, the service line or a private pole that looks damaged. Treat all of it as live.
- Fire, or anyone in danger. Call 000 first. Fire and rescue will make the scene safe and have the supply cut if it needs to be. Call us after that, not instead of it.
Call 0485 824 714 and describe what you can see from somewhere safe. You get someone who does this work, not a call centre, and they will tell you straight away whether it has to be made safe tonight or whether it can wait until morning.
0485 824 714On the tools in Narwee
The work we do around Narwee
A sense of what actually comes up here, and why. If yours looks like one of these, describe it on the phone and we will tell you what is involved.
Consumer mains upgrade
Original mains feeding a house that had since picked up ducted air conditioning and an induction cooktop. Upgraded the mains and the board together.
Typically the post-war housing around the station.
It is one of the more common calls we take in this part of Sydney.
More on thisOverhead service line replacement
Service line down after a storm. Made the site safe, replaced the damaged section and had the property back on supply the same day.
Typically the post-war housing around the station.
More on thisPoint of attachment replacement
The attachment had pulled away from the fascia and was taking the weight of the span on two screws. Replaced properly into sound timber and re-tensioned the line.
Typically the post-war housing around the station.
More on this
Something similar at your place? Call 0485 824 714 and describe it. Free quotes, 24 hours a day.
Ready to book?
How it works
A simple process for excellent service, right when you need it.
01Contact our team
Reach out by phone, email or the contact form to start the process.
02Discuss the details
Tell us what you need, including property information and any specific concerns.
03Assessment and quote
We schedule a visit or request photos, then provide a detailed quote and timeline.
04Confirmation and booking
Once the quote is approved we book your job at a time that suits you.
05Job completion
We arrive on time with every tool needed to finish the work properly.
06Final check and payment
We inspect and test the work before finalising the paperwork and compliance.
Network checker
Are you on Ausgrid or Endeavour Energy?
Every Level 2 job is lodged with the network that owns the wires in your street, and the paperwork differs between the two. Type your suburb and we will tell you which one you are on. We are accredited for both, so either way you are covered.
A guide only. Network boundaries can split a single street, so we always confirm the network before we lodge anything.
FAQs
Level 2 electrician Narwee, questions answered
What people in Narwee ask before they book. If yours is not here, call and ask.
Is it worth upgrading the mains at the same time as the switchboard?
Often, but not always, and it depends on what the mains actually are. Where they are damaged, undersized for the assessed demand, or unsuitable for how they are installed, doing both at once saves a second outage and a second set of distributor paperwork. Where the existing cable is sound and adequate, there is no reason to replace it.
Do I need new consumer mains with a switchboard upgrade?
Not automatically. They are separate parts of the installation. A switchboard can often be replaced on its own, and many switchboard projects can be completed by a licensed electrician. New consumer mains are required where the existing cable is damaged, unsuitable for the installation method, or too small for the assessed maximum demand. The assessment decides, not the age of the board.
What should I do if a service cable comes down in a storm?
Stay well clear, keep people and animals away, and treat the cable as energised even if the property has lost power. Contact your electricity distributor’s emergency line, and call 000 if anyone is in immediate danger. Once the site is safe, a Level 2 ASP repairs or replaces the service, and the work is tested and documented.
What is a CCEW and will I get one?
A Certificate of Compliance for Electrical Work. It is the legal record that the work meets AS/NZS 3000 and the NSW Service and Installation Rules. You get one on every job we do, and a copy goes to the distributor. Keep it: it is what you hand over at sale, and it is what an insurer asks for.
Who owns the wiring between the street and my switchboard?
The distributor owns the network up to the point of supply. From there the service into the building, the point of attachment, any pole standing on your own land and the consumer mains are generally the property owner’s assets, which makes their condition, repair and replacement the owner’s responsibility. It is worth confirming early, because ownership decides who pays.
Do I deal with the distributor or my electricity retailer?
Both, for different things. Your retailer sells you the electricity, handles the account and arranges the meter through a metering provider. The distributor owns the poles, wires and the connection itself. Physical work on the connection goes through an accredited Level 2 ASP, and we lodge the paperwork with the distributor on your behalf.
How long does this kind of work take?
A straightforward service line or point of attachment repair is usually a few hours on site. Consumer mains, a switchboard and metering together is commonly most of a day. What stretches a job is rarely the electrical work: it is the distributor application, an outage window that has to be booked, excavation and reinstatement, or approval in a strata building. We tell you which of those apply before you commit.
My board sits on an asbestos backing panel. Can it still be upgraded?
Yes. Boards installed before the 1990s often sit on backing panels containing asbestos. It is identified before the work starts and handled to the required procedure rather than being discovered halfway through. It affects the method, the time on site and the price. It does not affect whether the job can be done.
Do you charge more for after hours and weekend work?
Emergency and after-hours attendance is charged at a higher rate than planned work, and we tell you the rate on the phone before anyone is dispatched rather than on the invoice. Where a job is genuinely urgent, such as a cable down or burnt service equipment, it gets attended regardless of the hour. Where it can safely wait for a planned visit, we will say so, because that is the cheaper option for you.
What affects the cost of this work?
Whether the supply is overhead or underground, cable size and length, route and access, any excavation or reinstatement, whether metering or switchboard work is involved, how much distributor coordination is needed, and whether the job is planned or urgent. We quote once the scope is confirmed.
Is Narwee on Ausgrid or Endeavour Energy?
Narwee is generally within the Ausgrid distribution area. It matters because the application process and the paperwork differ between the two networks, and a form prepared for the wrong one goes nowhere. Boundaries can run through a single street, so we confirm the distributor and the supply arrangement for your individual address before lodging network work.
How fast can you get to Narwee?
We answer the phone 24 hours a day, seven days a week, and we aim for same day attendance where the job and our run allow it. Narwee is part of our regular the St George area run rather than somewhere we have to travel specially. Call, tell us what has happened, and we will tell you honestly when we can be there.

Get in touch
Need a Level 2 electrician in Sydney?
Metering, service mains, private poles, defect notices and emergency call outs. Tell us what is happening and we will tell you what it takes, what it costs and when we can be there. No obligation either way.
Tap to call, 24/70485 824 714- Free quote, no obligation
- A Level 2 electrician calls you back, not a call centre
- Emergency jobs answered around the clock
Request a call back
Tell us what you need. We reply within 30 minutes during business hours.